Visit our newest sister site!
Hundreds of free aircraft flight manuals
Civilian • Historical • Military • Declassified • FREE!


TUCoPS :: Phreaking Cellular - Other Manufacturers :: pana06.txt

Panasonic CM/TF800 Programming

Better a bottle in front of me than a frontal lobotomy.


PANASONIC CM/TF800

NOTES:  This is a dual NAM unit.
        The ESN prefix is 136 decimal & 88 hex.
        Panasonic: 201-392-6053


NAM PROGRAMING:

1.  Turn power on.

2.  Within 20 seconds enter * 0 # 0 * 0 # 0 * 1 for NAM 1
    or * 0 # 0 * 0 # 0 * 2 for NAM 2.

3.  Each data entry can be looked at by pressing RCL followed by the
    location (step) number below.

4.  To store new data enter the value, press STO followed by the location
    (step) number below.  For example to enter a system ID of 00031 enter
    00031 STO 01.  Data can be entered or reviewed in any order.

5.  At any time press STO * * to complete programing.

6.  Press END to exit.



PROGRAMING DATA:

STEP#    #OF DIGITS/RANGE    DISPLAY        DESCRIPTION

01       00000 - 32767       SIDH           SYSTEM ID
02       10 DIGITS           OWNDL          MIN (AREA CODE & TEL NUMBER)
03       0 OR 1              PRESYS         PREFERRED SYSTEM
04       333 OR 334          IPCH           INITIAL PAGING CHANNEL
05       2 DIGITS            ACCOLC         ACCESS OVERLOAD CLASS
06       2 DIGITS            GIM            GROUP ID (10 IN USA)
07       2 DIGITS            DLMT           DIALED DIGIT LIMIT (00= NO LIMIT)
08       08 ONLY             SCM            STATION CLASS MARK
09       UP TO 12 DIGITS     SPDL           SPEED DIAL NUMBER (PERMANENT
                                            NUMBER STORED IN LOCATION 00)
10       2 TO 4 DIGITS       LOCK           LOCK CODE
11       8 DIGIT, 0 OR 1     FCN 1          SEE NOTE 1 BELOW.
12       8 DIGIT, 0 OR 1     FCN 2          SEE NOTE 2 BELOW
13       8 DIGIT, 0 OR 1     FCN 3          SEE NOTE 3 BELOW


NOTES:

1.  Suggested entry is: 11000000.

Bit 7/Digit 1 = Local use Mark
Bit 6/Digit 2 = MIN Mark
Bit 5/Digit 3 = Not Used
Bit 4/Digit 4 = Not Used
Bit 3/Digit 5 = Not Used
Bit 2/Digit 6 = Horn Alert
Bit 1/Digit 7 = Radio Mute
Bit 0/Digit 8 = Not Used

2.  Suggested entry is: 00010100.

Bit 7/Digit 1 = Not Used
Bit 6/Digit 2 = Built in Monitor
Bit 5/Digit 3 = Auto Lock
(if set to 1 and unlock code is unknown phone will NOT enter program mode.)
Bit 4/Digit 4 = Full Lock
Bit 3/Digit 5 = Not Used
(Enable only one of the following)
Bit 2/Digit 6 = Allow user A/B select
Bit 1/Digit 7 = Preferred system only
Bit 0/Digit 8 = Home system only (no Roam)

3.  Suggested entry is: 11000111.

Digit 1 = Received call indicator
Digit 2 = Continuous DTMF
Digit 3 = Not Used
Digit 4 = Dial Lock
Digit 5 = Not Used
Digit 6 = Enable permanent timer (FCN 1)
Digit 7 = Enable resetable timer (FCN 2)
Digit 8 = Enable individual call timer


READING ESN FROM HANDSET:

1.  Power up phone as above.

2.  Enter * 0 0 0 0 #.

3.  Press * 3 SND.

4.  Press 1 1 SND, phone will display decimal ESN, note that the leading
    "1" of the 136 ESN prefix will be omitted as the phone only has a ten
    digit display capacity.

LOCK: F 3 2 = Dial Lock, F 3 1 = Send lock, F 3 0 = Full lock

UNLOCK: Enter two to four digit code.


A/B SYSTEM SELECT:

1.  Phone will default to preferred/non-preferred on every power up.

2.  A only: F 7 2

3.  B only: F 7 3

4.  Home only: F 7 4 


TUCoPS is optimized to look best in Firefox® on a widescreen monitor (1440x900 or better).
Site design & layout copyright © 1986-2014 AOH